· efs:/efsprofiles/overideconfig = "
[SIPConfig:GeoLocation]
#enable or disable location info inclusion in regular calls
iEnableCellInfoInPANI = 0
#enable or disable location info inclusion in regular calls
iEnableLocInfoInNormalCall = 0
#enable or disable location info inclusion in emergency calls
iEnableLocInfoInEmergencyCall = 1
#to set the threshold for uncertainty validation
fUnCertaintyThreshold = 0.0
[QIPCALL:H264_2]
#This config is to specify the profile for H264. Only use value 1
#The possible values of this enum are:
#/** Invalid Profile*/
#QP_CONFIG_IMS_H264_PROFILE_INVALID = 0x00,
#/** Baseline Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_BASELINE = 0x01,
#/** Main Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_MAIN = 0x02,
#/** Extended Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_EXTENDED = 0x03,
#/** High Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_HIGH = 0x04
profile = 1
#Preffered resolution. Possible values:
#INVALID_RESOLUTION = 0,
#PORTRAIT_SQCIF_RESOLUTION, // 1
#LANDSCAPE_SQCIF_RESOLUTION, // 2
#PORTRAIT_QQVGA_RESOLUTION, // 3
#LANDSCAPE_QQVGA_RESOLUTION, // 4
#PORTRAIT_QCIF_RESOLUTION, // 5
#LANDSCAPE_QCIF_RESOLUTION, // 6
#PORTRAIT_QVGA_RESOLUTION, // 7
#LANDSCAPE_QVGA_RESOLUTION, // 8
#PORTRAIT_CIF_RESOLUTION, // 9
#LANDSCAPE_CIF_RESOLUTION, // 10
#PORTRAIT_VGA_RESOLUTION, // 11
#LANDSCAPE_VGA_RESOLUTION, // 12
#PORTRAIT_HD_720_RESOLUTION, // 13
#LANDSCAPE_HD_720_RESOLUTION, // 14
resolution_preferred = 8
#Preffered Framerate
framerate_preferred = 15
#payload type for packetization mode 0. number above 96
payload_type_packetization_mode0 = 117
#Codec level. possible values:
#INVALID_LEVEL = 0x00,
#Level 1 = 0x01,
#Level 1B = 0x02,
#Level 11 = 0x03,
#Level 12 = 0x04,
#Level 13 = 0x05,
#Level 2 = 0x06,
#Level 21 = 0x07,
#Level 22 = 0x08,
#Level 3 = 0x09,
#Level 31 = 0x0A,
#Level 32 = 0x0B,
#Level 4 = 0x0C,
#Level 41 = 0x0D,
#Level 42 = 0x0E,
#Level 5 = 0x0F,
#Level 51 = 0x10
level = 4
#payload type for packetization mode 1. number above 96 and
#different from packetization mode 0
payload_type_packetization_mode1 = 118
#AS value if IPv6 is used
ipv6_AS_value = 0
#Max Bitrate
bitrate_max = 335
#Preffered bitrate
bitrate_preferred = 335
#Min Bitrate
bitrate_min = 64
#Max Framerate
framerate_max = 15
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
#Min Framerate
framerate_min = 7
#Supported resolution
resolutions_supported = 0
#AS value if IPv4 is used
ipv4_AS_value = 0
[QIPCALL:H264_1]
#This config is to specify the profile for H264. Only use value 1
#The possible values of this enum are:
#/** Invalid Profile*/
#QP_CONFIG_IMS_H264_PROFILE_INVALID = 0x00,
#/** Baseline Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_BASELINE = 0x01,
#/** Main Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_MAIN = 0x02,
#/** Extended Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_EXTENDED = 0x03,
#/** High Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_HIGH = 0x04
profile = 1
#Preffered resolution. Possible values:
#INVALID_RESOLUTION = 0,
#PORTRAIT_SQCIF_RESOLUTION, // 1
#LANDSCAPE_SQCIF_RESOLUTION, // 2
#PORTRAIT_QQVGA_RESOLUTION, // 3
#LANDSCAPE_QQVGA_RESOLUTION, // 4
#PORTRAIT_QCIF_RESOLUTION, // 5
#LANDSCAPE_QCIF_RESOLUTION, // 6
#PORTRAIT_QVGA_RESOLUTION, // 7
#LANDSCAPE_QVGA_RESOLUTION, // 8
#PORTRAIT_CIF_RESOLUTION, // 9
#LANDSCAPE_CIF_RESOLUTION, // 10
#PORTRAIT_VGA_RESOLUTION, // 11
#LANDSCAPE_VGA_RESOLUTION, // 12
#PORTRAIT_HD_720_RESOLUTION, // 13
#LANDSCAPE_HD_720_RESOLUTION, // 14
resolution_preferred = 8
#Preffered Framerate
framerate_preferred = 15
#payload type for packetization mode 0. number above 96
payload_type_packetization_mode0 = 115
#Codec level. possible values:
#INVALID_LEVEL = 0x00,
#Level 1 = 0x01,
#Level 1B = 0x02,
#Level 11 = 0x03,
#Level 12 = 0x04,
#Level 13 = 0x05,
#Level 2 = 0x06,
#Level 21 = 0x07,
#Level 22 = 0x08,
#Level 3 = 0x09,
#Level 31 = 0x0A,
#Level 32 = 0x0B,
#Level 4 = 0x0C,
#Level 41 = 0x0D,
#Level 42 = 0x0E,
#Level 5 = 0x0F,
#Level 51 = 0x10
level = 4
#payload type for packetization mode 1. number above 96 and
#different from packetization mode 0
payload_type_packetization_mode1 = 116
#AS value if IPv6 is used
ipv6_AS_value = 0
#Max Bitrate
bitrate_max = 335
#Preffered bitrate
bitrate_preferred = 335
#Min Bitrate
bitrate_min = 64
#Max Framerate
framerate_max = 15
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
#Min Framerate
framerate_min = 7
#Supported resolution
resolutions_supported = 0
#AS value if IPv4 is used
ipv4_AS_value = 0
[QIPCALL:H264_0]
#This config is to specify the profile for H264. Only use value 1
#The possible values of this enum are:
#/** Invalid Profile*/
#QP_CONFIG_IMS_H264_PROFILE_INVALID = 0x00,
#/** Baseline Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_BASELINE = 0x01,
#/** Main Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_MAIN = 0x02,
#/** Extended Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_EXTENDED = 0x03,
#/** High Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_HIGH = 0x04
profile = 1
#Preffered resolution. Possible values:
#INVALID_RESOLUTION = 0,
#PORTRAIT_SQCIF_RESOLUTION, // 1
#LANDSCAPE_SQCIF_RESOLUTION, // 2
#PORTRAIT_QQVGA_RESOLUTION, // 3
#LANDSCAPE_QQVGA_RESOLUTION, // 4
#PORTRAIT_QCIF_RESOLUTION, // 5
#LANDSCAPE_QCIF_RESOLUTION, // 6
#PORTRAIT_QVGA_RESOLUTION, // 7
#LANDSCAPE_QVGA_RESOLUTION, // 8
#PORTRAIT_CIF_RESOLUTION, // 9
#LANDSCAPE_CIF_RESOLUTION, // 10
#PORTRAIT_VGA_RESOLUTION, // 11
#LANDSCAPE_VGA_RESOLUTION, // 12
#PORTRAIT_HD_720_RESOLUTION, // 13
#LANDSCAPE_HD_720_RESOLUTION, // 14
resolution_preferred = 13
#Preffered Framerate
framerate_preferred = 30
#payload type for packetization mode 0. number above 96
payload_type_packetization_mode0 = 0
#Codec level. possible values:
#INVALID_LEVEL = 0x00,
#Level 1 = 0x01,
#Level 1B = 0x02,
#Level 11 = 0x03,
#Level 12 = 0x04,
#Level 13 = 0x05,
#Level 2 = 0x06,
#Level 21 = 0x07,
#Level 22 = 0x08,
#Level 3 = 0x09,
#Level 31 = 0x0A,
#Level 32 = 0x0B,
#Level 4 = 0x0C,
#Level 41 = 0x0D,
#Level 42 = 0x0E,
#Level 5 = 0x0F,
#Level 51 = 0x10
level = 10
#payload type for packetization mode 1. number above 96 and
#different from packetization mode 0
payload_type_packetization_mode1 = 0
#AS value if IPv6 is used
ipv6_AS_value = 0
#Max Bitrate
bitrate_max = 2052
#Preffered bitrate
bitrate_preferred = 2052
#Min Bitrate
bitrate_min = 64
#Max Framerate
framerate_max = 30
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
#Min Framerate
framerate_min = 7
#Supported resolution
resolutions_supported = 1104
#AS value if IPv4 is used
ipv4_AS_value = 0
[QIPCALL:EVS_0]
#channel aware setting
ch_aw_recv = -1
#This config is used for hf only
hf_only = 0
#This config is bandwidth.
#enum - BW_NB, BW_WB, BW_SWB, BW_FB, BW_NB_WB, BW_NB_SWB, BW_NB_FWB,
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
Bandwidth = BandWidth_SWB
#This config is used for bit rate. It has to be in DECIMAL format.
BitRate = 120
[QIPCALL:EVS_1]
#channel aware setting
ch_aw_recv = 2
#This config is bandwidth.
#enum - BW_NB, BW_WB, BW_SWB, BW_FB, BW_NB_WB, BW_NB_SWB, BW_NB_FWB,
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
Bandwidth = BandWidth_SWB
#This config is used for bit rate.
BitRate = 120
[QIPCALL:EVS_2]
#channel aware setting
ch_aw_recv = -1
#This config is bandwidth.
#enum - BW_NB, BW_WB, BW_SWB, BW_FB, BW_NB_WB, BW_NB_SWB, BW_NB_FWB,
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
Bandwidth = BandWidth_WB
#This config is used for bit rate.
BitRate = 127
[SMSDAN:USSDSettings]
#This config item controls the Language String to be used.
ussdLangString = ""
[QIPCALL:H265_2]
#payload type for packetization mode 0. number above 96
payload_type = 0
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
[Registration:RegistrationTimers]
#This config item controls the time in seconds to wait for WLAN RAT in wifi preferred mode for SSIM device
wlanGaurdTimer = 7
#This config item controls the Register configuration for the network-initiated De reg Timer value.
networkInitiatedDeRegistrationTimer = 0
#This config item controls the waiting time for sending Reg or Dereg. Unit is ms.
FTConsolidateTimer = 0
#This config item controls the Retry timer for permanent PDP failures
pdnRetryLongTimer = 10
#This config item controls the time in seconds to wait for WLAN RAT in wifi preferred mode for MSIM device
wlanGaurdTimerMSIM = 7
#This config item controls the time in seconds to wait for WWAN RAT in cellular preferred mode for SSIM device
wwanGaurdTimer = 7
#This config item controls the time in seconds to wait for WWAN RAT in cellular preferred mode for MSIM device
wwanGaurdTimerMSIM = 10
#This config item controls the Retry timer for temporary failures
pdnRetryShortTimer = 60
[QIPCALL:H265_0]
#payload type for packetization mode 0. number above 96
payload_type = 0
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
[QIPCALL:H265_1]
#payload type for packetization mode 0. number above 96
payload_type = 0
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
[Ut:UtConfiguration]
#This config is required to configure the server responses for which UT is to be blocked permanently
BlockUtResponseCodes = "401,400, 403, 500, 502, 503, 504"
#This config item controls the media element type for Call Barring Service. Possible values for override are as follows:
#QP_NO_MEDIA_TAG = 0 -->No media tag support
#QP_ONLY_VIDEO_TAG_FOR_VT = 1 -->One media tag per media type
#QP_AUDIO_AND_VIDEO_TAGS_FOR_VT = 2 -->include both audio and video tags
#QP_NO_MEDIA_TAG_FOR_VOICE_AND_ONLY_VIDEO_TAG_FOR_VT = 3 -->include Only video tag
mediaElementSupportForCB = 0
#This config item specifies if the realm is to trimmed or not. 0:Not enabled(default), 1:enabled
isTrimRealmEnabled = 0
#This config item specifies if IR92v10 is enabled or not. 0:Not enabled(default), 1:enabled
isIr92V10Enabled = 0
#This config item controls the time for which the PDN needs to be kept Active after a SS request is completed
pdnHysTimerValue = 0
#This config item controls the Maximum time within which a Response should be sent to UI
maxResponseTimerValue = 5
#This config item specifies if CFNL request is blocked with CFNRc. 0:Not enabled(default), 1:enabled
isCFNLBlockedwithCFNRc = 0
#This config item controls the action item when there is no SIB value for CB request. Possible values for override are as follows:
#QP_NO_HANDLING = 0 --> Default
#QP_REJECT_EMPTY_SIB = 1 --> Reject
#QP_AUDIO_RULE_ONLY = 2 --> Audio Only
#QP_AUDIO_AND_VIDEO_RULES = 3 --> Both Audio and Video
emptySIBUsageForCB = 0
#This config item controls the action item. When a rule id is not present in a server xml, a request is not allowed. It is used on VDF-Portugal only now. 0:Not to check a rule ID(Default), 1:Block a request when rule ID is not present in a server xml
blockIfRuleIDAbsent = 0
#This config item specifies if the GET request is to be sent at simservs node level. 0:Not enabled(default), 1:enabled
isReqAtSimservsNode = 0
[SIPConfig:FeatureFlags]
#enable or disable sip instance inclusion in contact header
IsSipInstanceNeeded = 0
#enable or disable Cellular-Network-Info header
IsCNIEnabled = 1
#enable or disable IsUserPartNeededForContactHeader
IsUserPartNeededForContactHeader = 1
#enable or disable header compact form
IsCompactFormEnabled = 0
#enable or disable IsUIReadyStatusCheckNeeded
IsUIReadyStatusCheckNeeded = 0
#disable StopTimerBon1xx once 1xx response is not received
StopTimerBon1xx = 0
#enable or disable IsImsiNeededForContactHeader
IsImsiNeededForContactHeader = 0
[QIPCALL:ImsVoiceSrvccConfig]
#This config is required to enable SRVCC based on contact header FT.
enableSRVCCOnContactHeader = 0
#This config is required to enable bSRVCC.
bSrvccEnabled = 1
#This config is required to enable aSRVCC.
aSrvccEnabled = 1
#This config is required to enable mid call SRVCC.
midcallSrvccEnabled = 1
[QIPCALL:ImsRtcpConfig]
#This config is required to configure the RR bandwidth for Video.
rrForVideo = 2000
#This config is required to configure the timer for RTCP
#monitoring.
rtcpLinkAlivenessTimer = 20
#This config is required to configure the RS bandwidth for Audio.
rsForAudio = 600
#This config is required to disbale/enable the RTCP monitoring.
disableRTCPMonitoring = 0
#This config is required to configure the timer for RTCP
#Reporting in VT call.
rtcpReportingIntervalInVideo = 1
#This config is required to configure the RS bandwidth for Video.
rsForVideo = 600
#This config is required to configure the RR bandwidth for Audio.
rrForAudio = 2000
[QIPCALL:AMR_4]
#This config is bandwidth.
#enum - BW_NW, BW_WB
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
BandWidth = BandWidth_WB
#This config is modeset.
ModeSet = 0
#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA
#Possible INTEGER values for Mode are as follows:
#0 --> AMR_MODE_BE
#1 --> AMR_MODE_OA
#2 --> AMR_MODE_MAX
Mode = AMR_MODE_OA
[QIPCALL:G711_2]
#This config is dtx.
#0 - dtx disable
#1 - dtx enable
Dtx_enable = 1
#This config is to set G711 mode
#enum - G711_MODE_PCMU, G711_MODE_PCMA
#Possible INTEGER values for override Mode mask values are as follows:
#0 --> G711_MODE_PCMU
#1 --> G711_MODE_PCMA
#2 --> G711_MODE_MAX
Mode = G711_MODE_PCMA
[QIPCALL:G711_1]
#This config is dtx.
#0 - dtx disable
#1 - dtx enable
Dtx_enable = 1
#This config is to set G711 mode
#enum - G711_MODE_PCMU, G711_MODE_PCMA
#Possible INTEGER values for override Mode mask values are as follows:
#0 --> G711_MODE_PCMU
#1 --> G711_MODE_PCMA
#2 --> G711_MODE_MAX
Mode = G711_MODE_PCMU
[QIPCALL:G711_0]
#This config is dtx.
#0 - dtx disable
#1 - dtx enable
Dtx_enable = 1
#This config is to set G711 mode
#enum - G711_MODE_PCMU, G711_MODE_PCMA
#Possible INTEGER values for override Mode mask values are as follows:
#0 --> G711_MODE_PCMU
#1 --> G711_MODE_PCMA
#2 --> G711_MODE_MAX
Mode = G711_MODE_PCMU
[QIPCALL:AMR_0]
#This config is bandwidth.
#enum - BW_NW, BW_WB
#Possible INTEGER values for Bandwidth are as follows
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
BandWidth = BandWidth_NB
#This config is modeset.
ModeSet = 0
#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA
#Possible INTEGER values for Mode are as follows:
#0 --> AMR_MODE_BE
#1 --> AMR_MODE_OA
#2 --> AMR_MODE_MAX
Mode = AMR_MODE_BE
[QIPCALL:AMR_1]
#This config is bandwidth.
#enum - BW_NW, BW_WB
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
BandWidth = BandWidth_WB
#This config is modeset.
ModeSet = 0
#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA
#Possible INTEGER values for Mode are as follows:
#0 --> AMR_MODE_BE
#1 --> AMR_MODE_OA
#2 --> AMR_MODE_MAX
Mode = AMR_MODE_BE
[QIPCALL:AMR_2]
#This config is bandwidth.
#enum - BW_NW, BW_WB
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
BandWidth = BandWidth_NB
#This config is modeset.
ModeSet = 0
#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA
#Possible INTEGER values for Mode are as follows:
#0 --> AMR_MODE_BE
#1 --> AMR_MODE_OA
#2 --> AMR_MODE_MAX
Mode = AMR_MODE_OA
[QIPCALL:AMR_3]
#This config is bandwidth.
#enum - BW_NW, BW_WB
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
BandWidth = BandWidth_NB
#This config is modeset.
ModeSet = 0
#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA
#Possible INTEGER values for Mode are as follows:
#0 --> AMR_MODE_BE
#1 --> AMR_MODE_OA
#2 --> AMR_MODE_MAX
Mode = AMR_MODE_BE
[QIPCALL:ImsVoiceQoSConfig]
#This config is required to enable sending SDP answer in PRACK
#for 183 if the local qos is granted before 183 response is recvd by
#the UE.
qosOptimization = 0
#This config is required to configure the timer for dedicated
#bearer allocation.
qosReservationTimer = 8000
#This config is required to enable set the desired qos strength
#for local and remote UEs.
qosDesiredStrength = 1
#This config is required to enable 183 for Reneg
qosMc183 = 0
#This config is required to configure if the UE must wait for
#video dedicated bearer allocation during call setup.
localQosResReqVideo = 1
#This config is required to configure if the UE must wait for
#text dedicated bearer allocation during call setup.
localQosResReqText = 1
#This config is required to enable qos call flow when call is on wifi
simulateQoSInWifi = 0
#This config is required to enable/disable video CRBT feature
VideoCRBT = 0
#This config is required to configure the early QoS timer for video dedicated
#bearer allocation.
earlyQosReservationTimer = 0
#This config is required to enable Qos precondition negotiation
#in SDP.
qosPreconditionsEnabled = 1
#This config is required to enable Qos MC precondition negotiation
#in SDP.
qosMcPreconditionsEnabled = 0
#This config is required to configure the MBR threshold.
iMBRthresholdValue = 0
#This config is required to configure if the UE must wait for
#audio dedicated bearer allocation during call setup.
localQosResReqAudio = 1
#This config is required to configure if the initial SDP
#directionality should be inactive in REINVITE when preconditions are
#used
reinviteSdpDirInactive = 0
#This config is required to enable MBR check for video bearer.
qosMbrVideoCheckReqEnabled = 1
#This config is required to configure if the initial SDP
#directionality should be inactive when preconditions are used.
inviteSdpDirInactive = 0
#This config is required to start Mid-call qos timer after HO from Wifi to LTE is success
startMcqosAfterHOfromWifitoLte = 1
#This config is required to enable MBR check for audio bearer.
qosMbrAudioCheckReqEnabled = 0
#This config is required to enable QCI match with the requested media type for qos
checkQciForQoSMediaType = 0
#This config is required to enable mid-call precondition for Call Hold/Resume
qosMcHold = 0
[Ut:XCAPCommonHC]
#This config item controls whether GBA_U is enabled or not
useGBAMEOnly = 0
#This config item controls whether ims prefix is added or not for Ub request like as bsf.ims.mnc005.mcc232.pub.3gppnetwork.org
includeIMSPrefixForUSIM = 0
#This config item controls whether to ignore RSp Auth failure or not
IgnoreRSPAuthFailure = 0
#This config item controls the configuration of BSF server address
bsfServerAddress = ""
#This config item controls whether to use user mode for TLS
useUserModeForTLS = 0
#This config item controls whether BSF server supports TLS. Possible values for override are as follows:
#eQP_IMS_XCAP_GBA_TLS_MODE_OVER_UB_NONE = 0 --> not enabled
#eQP_IMS_XCAP_GBA_TLS_MODE_OVER_UB_ON = 1 --> Enabled
bsfServerTlsSupport = 0
[Registration:RegistrationFeatureFlags]
#This config item specifies if the sub operator is APTG and special handling is required for Options unsubscribed error or not. 0:Not enabled(default), 1:enabled
optionsUnsubscribedSpecialHandling = 0
#This config item controls whether need to reset AWT timer.
notResetAWTTimerEnable = 0
#This config item controls whether Perm block over IWLAN need to reset or not.
resetPermblockOverIwlan = 0
#This config item controls whether IWLAN Config failure is to be handled as internal failure.
specialhandlingForIWLANConfigFailure = 0
#This config item controls whether measurement on IWLNA should be ignored during APM on.
IgnoreWiFiMeasurementDuringAPMOn = 0
[QIPCALL:EVS_3]
#channel aware setting
ch_aw_recv = 2
#This config is bandwidth.
#enum - BW_NB, BW_WB, BW_SWB, BW_FB, BW_NB_WB, BW_NB_SWB, BW_NB_FWB,
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
Bandwidth = BandWidth_WB
#This config is used for bit rate.
BitRate = 120
[QIPCALL:ImsVoiceSessionTimerConfig]
#This config is required to configure the session refresher shall
#be UAC/UAS.
#Possible enum values are as follows:
#QP_CONFIG_SES_REFRESHER_UAC =0, UAC will go out as the refresh parameter in the initial Refresh Request
#QP_CONFIG_SES_REFRESHER_UAS =1, UAS will go out as the refresh parameter in the initial Refresh Request
#QP_CONFIG_SES_REFRESHER_UNKNOWN =2 UNKNOWN
sessionRefresherType = QP_CONFIG_SES_REFRESHER_UAC
#This config is required to enable session timer support.
sessionTimerEnabled = 1
#This config is required to enable Stand Alone Session Expiry
#negotiation.
standAloneEnabled = 1
#This config is required to enable Sesssion Expiry timer
#negotiation.
allowSeNegotiation = 0
#This config is required to configure the method for session
#referesh shall be REINVITE/UPDATE.
#Possible enum values are as follows:
#QP_CONFIG_SES_REFRESH_UNKNOWN = -1, UNKNOWN
#QP_CONFIG_SES_REFRESH_INVITE, INVITE will be the refresh method used
#QP_CONFIG_SES_REFRESH_UPDATE
sessionRefresherMethod = QP_CONFIG_SES_REFRESH_UPDATE
[QIPCALL:ImsVoiceConfig]
#This config is required to configure the Emergency call Cancel Timer.TImer is started when UE triggered CANCEL and waiting for 200 OK of CANCEL from network
emergencyCallCancelTimer = 500
#This config is required to configure the default WPS invite duration.
wpsInviteDuration = 0
#This config is required to enable 380 response validation as per
#3GPP.
enableAlternateSrvRspCheck = 0
#This config is required to set the display text priority
#subscription.
displayTextPriority = 3
#This config is required to include MTT USSD feature tag into IMS registration.
ussdAcceptContact = "+g.3gpp.nw-init-ussi"
#This config is required to configure the default invite retry counter.
inviteRetryCounter = 2
#This config is required to select the default emergency URI if sub category matches with multiple entries
e911SelectDefURI = 0
#This config is required to configure Call Waiting indication to UI
enableCWI = 0
#This config is required to disable early media timer.
disableEarlyMediaTimer = 0
#This config is required to configure the voice call Cancel Timer.TImer is started when UE triggered CANCEL and waiting for 200 OK of CANCEL from network
voiceCallCancelTimer = 0
#This config is required to place AMR WB before AMR in encryption call.
preferAMRWBinEncryptionCall = 0
#This config is required to enable PEM header in 183.
enablePEMHeaderIn183 = 0
#This config is required to configure the default URI type
#(SIP/TEL) for MO calls.
#Possible INTEGER values for the enum are as follows:
#QPE_IMS_URI_INIT = 0, enum value 0
#QPE_IMS_URI_SIP = QPE_IMS_URI_INIT, enum value 0
#QPE_IMS_URI_TEL, enum value 1
#QPE_IMS_URI_ANY, enum value 2
#QPE_IMS_URI_MAX enum value 3
uriType = QPE_IMS_URI_TEL
#This config is required to configure the enabling of sending REINVITE
#during Active calls HO.
reInviteonHOforActiveCalls = 0
#This config is required to accommodate Network issue with symmetric payload for both TX/RX stream from Remote UE
supportSymmetricPTforTxRx = 0
#This config is required to configure the terminating identity presentation or restriction type.
terminatingIdentityService = 0
#This config is required to configure the default WPS fallback duration.
wpsFallbackDuration = 0
#This config is required to enable the playing of local hold tone.
enableLocalHoldTone = 0
#This config is required to configure the ignoring of AS value
ignoreASValidation = 0
#This config is required to disable the default jitter buffer config
disableDefaultJBConfig = 0
#This config is required to configure the max-red value
max_red = 0
#This config is required to set error code for CT submode.
sessionEndResponseTimeout = 0
#This config is required to enable VoWIFI Call Continuity to LTE NonVOPS.
enableVCCtoLTENonVOPS = 0
#This config is required to enable the propagation of multiple 180 to UI.
enableMultiple180PropagationToUI = 0
#This config is required to enable emergency call operation in CS-only mode.
emergCallCSOnly = 0
#This config is required to configure number format during roaming, geo-local/home-local
#The possible INTEGER values for this enum are as follows:
#QPE_IMS_PHONE_CONTEXT_GEO_LOCAL = 0,
#QPE_IMS_PHONE_CONTEXT_HOME_LOCAL = 1
phoneContextPolicy = QPE_IMS_PHONE_CONTEXT_GEO_LOCAL
#This config is required to decide whether AMR BE fallback needs to be disabled
disableAMRBEFallBack = 0
#This config is required to consider a Normal call for end on Re-Reg Failure.
#e911 calls are by default allowed to continue till network tears it down.
endCallOnReRegFailure = 0
#This config is required to set reason Header Type.
reasonHeaderCustomizationType = 0
#This config is required to enable Call end on RTP inactivity.
CallEndonRTPInactivity = 0
#This config is required to set the phone context domain source.
#Possible INTEGER values for this enum are as follows:
#QPE_IMS_PHONE_CONTEXT_SOURCE_FROM_MCC_MNC = 0,
#QPE_IMS_PHONE_CONTEXT_SOURCE_FROM_PAU_HEADER = 1,
#QPE_IMS_PHONE_CONTEXT_SOURCE_PRE_DEFINED = 2,
PhoneContextSource = QPE_IMS_PHONE_CONTEXT_SOURCE_FROM_MCC_MNC
#This config is required to set preconditions enabled with qos events ignored.
ignoreQOSEvents = 0
#This config is required to enable the MT USSI.
enableMTUSSI = 1
#This config is required to configure the privacy type. Set 0: for none, 1: for id, 2: for header.
privacyType = 2
#This config is required to retain local SDP direction when incoming message has no PEM header.
PEMRetainLocalDirOnPeerNone = 0
[Registration:RegistrationDefaultParams]
#This config item will be used to configure default UserName to register with Network
userName = ""
#This config item will be used to configure default authType to register with Network
authType = ""
#This config item will be used to configure default Display Name to register with Network
displayName = ""
#This config item will be used to configure default DomainName to register with Network
domainName = ""
#This config item will be used to configure default authSecertKey
authSecertKey = "465b5ce8b199b49faa5f0a2ee238a6bc"
#This config item will be used to configure default Private URI to register with Network
privateURI = ""
#This config item will be used to configure default is3GPP
is3GPP = 0
#This config item will be used to configure default Realm to register with Network
realm = ""
#This config item will be used to configure default public URI to register with Network
publicURI = ""
#This config item will be used to configure default Password to register with Network
password = ""
[QIPCALL:ImsVoiceSuppsConfig]
#This config is required to configure the timer for Notify
#response to Refer.
notifyReferRspTimer = 20
#This config is required to end the conference call automatically
#when all other participants left the call.
endConfCallUponNoParticipant = 1
#This config is required to enable presentation of the call to
#the user when UE is already in two calls (active and held).
*presentThirdCalltoUser = 1
#This config is required to skip dialing out status participent from adding in conference list.
skipDialingOutStatus = 0
#This config is required to configure the conference event
#package subscription timer.
confEvtSubTimer = 3600
#This config is required not to send unsubscribe to NW for conference call when there is
#no notify-terminated received.
isUnsubcribeDisabled = 0
#This config is required to configure the dialog for the
#conference event subscribe request.
confEvtSubOutOfDialog = 0
#This config is required to configure the three party conf URI
#for KDDI.
threePartyConfFactoryUri = ""
#This config is required to end the conference call automatically
#when user-count node in the CEP XML is 1.
endConfCallBasedOnUserCountNode = 0
#This config is required to enable the conference event package
#subscription.
#Possible enum values are as follows:
#QPE_IMS_CONF_PCKG_NONE = 0,
#QPE_IMS_CONF_PCKG_ALL = 1,
#QPE_IMS_CONF_PCKG_ORIGINATOR_ONLY = 2,
#QPE_IMS_CONF_PCKG_ORIGINATOR_ONLY_NO_JOIN_IND = 3,
#QPE_IMS_CONF_PCKG_PARTICIPANT_NO_SUBSCRIBE_NO_INDICATION = 4
confEvtPakageEnabled = QPE_IMS_CONF_PCKG_ORIGINATOR_ONLY
[QIPCALL:ImsRtcpXRConfig]
#This config is required to enable RTCP-XR support.
rtcpXrEnabled = 0
[SMSDAN:DANSettings]
#This config item controls QIPCall 1x SMS and Voice Enabled (0:DAN SMS can be sent only if there is no voice call.
#1:Enabled; DAN and MO SMS can be sent even when a voice call is up).
smsAndVoiceOver1x = 0
#This NV item is used for configuring the transport channel preference on which DAN is to be sent.
channelPreference = 0
#This config item controls the DAN Retry Timer Interval Duration (In ms)
retryTimer = 0
#This config item controls the DAN Max Retry Counter
maxRetryCount = 0
#This NV item is used for controlling DAN Hysterisis Timer Duration
hysterisisTimer = 0
[QIPCALL:H263_0]
#payload type number above 96
payload_type = 0
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
[Registration:RegistrationCounters]
#This config item controls the Immediate Retry timer for failures
maxPDNIntermediateRetries = 1
[QIPCALL:ImsVideoConfig]
#This config is required to set the hold_downgrade_supported for VT
#calls.
hold_downgrade_supported = 0
#This config is required to configure the LTR mode.
#Possible enum values are as follows:
#/** Always disabled */
#QP_CONFIG_IMS_LTR_DISABLED = 0x00,
#/** Only enable for qc to qc devices negotiated via SDP */
#QP_CONFIG_IMS_LTR_ENABLED_RESTRICT_QC = 0x01,
#/** Always enabled */
#QP_CONFIG_IMS_LTR_ENABLED_ALL = 0x02,
ltrMode = QP_CONFIG_IMS_LTR_DISABLED
#This config is required to configure if VT capability can be impacted by modile data.
vtImpactedByMobileData = 1
#This config is required to set the video_capability_for_invite_no_sdp for
#incoming INVITE without SDP.
video_capability_for_invite_no_sdp = 1
#Internal:This config is required to store peer supported
#services
trackPeerServices = 1
[SIPConfig:Transport]
#above this size choose TCP and value 0 means disable tcp port open on UE
TCPThresholdValue = 1230
#enable or disable TCP Static threshold
TCPEnableStaticThreshold = 0
[SIPConfig:StandardTimers]
#sip registration expires value in milliseconds
SipRegValue = 0
#sip reg subscription expires value in milliseconds
SipSubscribeValue = 0
[SIPConfig:IPSec]
#integrity scheme for ipsec sip messages
#Possible INTEGER values for override Integrity Algorithm mask values are as follows:
#0 --> Invalid - none of the algorithm is supported
#1 --> alg=hmac-sha-1-96
#2 --> alg=hmac-md5-96
#3 --> alg=hmac-sha-1-96 and alg=hmac-md5-96
IntScheme = 3
#encryption algo for ipsec sip messages
#Possible INTEGER values for override Encryption Algorithm mask values are as follows:
#0 --> Invalid - none of the algorithm supported
#1 --> ealg=null;
#2 --> ealg=aes-cbc;
#3 --> ealg=null; ealg=aes-cbc;
#4 --> ealg=des-ede3-cbc;
#5 --> ealg=des-ede3-cbc; ealg=null;
#6 --> ealg=des-ede3-cbc; ealg=aes-cbc;
#7 --> ealg=des-ede3-cbc; ealg=aes-cbc; ealg=null;
EncAlgo = 7
[IMS_COMMON:ImsCommonTestModeCellId]
#This config item controls the test mode value
#eCELLID_TEST_MODE_OFF 0
#eCELLID_TEST_MODE_ON 1
CellID_Test_Mode = 0
#This config item controls the Cell ID value
CellID = ""
[SMSDAN:SMSSettings]
#This config item used to configure the error code and used while reject Incoming MT sms while NAS is busy in service one SMS.
IncomingSmsRejectCode = 400
#This config is required to enable addition of Accept-contact header field in MO SMS.
smsAcceptContactEnabled = 0
#This config item controls the SMS Feature tag
smsAcceptContact = "+g.3gpp.smsip"
#This config item used to enable or disable feature of rejecting incoming SMS when IMS is already processing a SMS.
EnableIncomingSmsRejectFeature = 0
[MEDIA:MediaCommon]
#This config item specifies if overall rate adaptation feature is enabled or not.
audioRAEnable = 1
#This config item specifies if NO_DATA format rtp pkts send is enabled or not.
rtpNoDataSend = 0
#This config item specifies maximum mtu size for the rtp packet
mtuSize = 1400
#This config item specifies packet exchange mode.
#enum:
#/** use OOB mode. In VS arch it will be same as mode 4*/
#QP_OOB_MODE = 0,
#/** use mailbox mode and CDRX length from ML1.
#Sync ADSP with CDRX ref time all the time i.e. at the beginning of the call
#as well as any resync at the middle of the call */
#QP_MB_FULL_CDRX_FULL_SYNC = 1,
#/** use mailbox mode and default CDRX length to 20ms.
#Sync ADSP with CDRX ref time at the beginning of the call
#and disable any sync at the middle of the call */
#QP_MB_CDRX_20_SYNC_ONCE = 2,
#/** use mailbox mode and CDRX length from ML1.
#Sync ADSP with CDRX ref time at the beginning of the call
#and disable any sync at the middle of the call */
#QP_MB_FULL_CDRX_SYNC_ONCE = 3,
#/** use mailbox mode and use it as CDRX disabled
#i.e. default CDRX length to 20ms and no sync with CDRX at all */
#QP_MB_DISABLE_CDRX_SYNC = 4,
enableMailbox = QP_MB_FULL_CDRX_FULL_SYNC
[Registration:RegistrationSettings]
#This config item controls Registration over IWLAN in airplane mode
#Possible INTEGER values for override are as follows:
#QPE_ENABLE_REG_INLPM_INVALID = 0 --> Reserved, Not to be used.
#QPE_ENABLE_REG_INLPM_OFF = 1 --> Registration is not on IWLAN as well enabled during LPM ON.
#QPE_ENABLE_REG_INLPM_ON = 2 --> Registration is enabled on IWLAN during LPM ON.
enableRegistrationInLPM = 2
#This config item controls PCSCF IP fallback feature
pcscfBasedIPFallback = 0
#This config item controls TTY over IMS
enableTTYOverIMS = 0
#This config item controls Reregistration over WIFI during Activate 3G call
#Possible INTEGER values for override are as follows:
#eQP_IMS_REG_OVER_WIFI_WHILE_ACTIVE_GSM_CALL_DISABLED = 0 --> Reg over WiFi is enabled by default irrespective of calls.
#eQP_IMS_REG_OVER_WIFI_WHILE_ACTIVE_2G_3G_CALL = 1 --> Reg over WiFi is blocked during 2G/3G calls
#eQP_IMS_REG_OVER_WIFI_WHILE_ACTIVE_3G_CALL_ONLY = 2 --> Reg over WiFi is blocked only during 3G calls
#eQP_IMS_REG_OVER_WIFI_WHILE_ACTIVE_2G_CALL_ONLY = 3 --> Reg over WiFi is blocked only during 2G calls
BlockRegOverWifiWhileActiveCSCall = 1
#This config item controls Reregistration over WIFI during Activate 1x call
BlockRegOverWifiWhileActive1XCall = 0
[Ut:XcapHCConfigUserProfile]
#This config item controls the configured user name
configUserName = ""
#This config item controls the configured user name
configUserPassword = ""
[DPL:Common]
#This config is used to enable/disable Dynamic UserAgent update
DisableUserAgentUpdate = 0
#Timer Var to delay in sending ISIM STATUS after initialization
ISIMStatusTimerVar = 5
#This config item determines usage to read the SIM card parameters (ISIM, USIM ) etc
#Possible INTEGER values for override are as follows:
#QPE_CONFIG_IMS_FILE_READ = 0 --> File Read Param Source
#QPE_CONFIG_IMS_NV_READ = 1 --> NV Read Param Source
#QPE_CONFIG_IMS_CARD_READ = 2 --> Card Read Param Source to read from ISIM
#QPE_CONFIG_IMS_FILE_READ_AUTH_ENABLED = 3 --> File Read Param Auth enabled (ONLY for testing)
#QPE_CONFIG_IMS_USIM_FB_MODE_ENABLED = 4 --> USIM fallback enabled
ParamSrc = QPE_CONFIG_IMS_USIM_FB_MODE_ENABLED
[QIPCALL:ImsMediaProfileConfig]
#This config is required to video codec profile list on 4G.
VideoProfile1 = "H264_0"
#This config is required to audio codec profile list.
AudioProfile1 = "EVS_0_126;EVS_2_127;AMR_1_104;AMR_0_102"
[QIPCALL:ImsVoWifiConfig]
#This config is required to configure the information to be passed
#in P-Emergency-Info header.
PEIHeaderInfoForEmergency = 0
#This config is required to configure the wifi connectivity
#backoff timer.
wifiConnectivityBackoffTimer = 10
#This config is required to configure the 380 handling for Emergency calls
#Possible values are:
#0 -> Default behaviour present in the code
#1 -> Force CSFB
#2 -> Send Permanent failure
Handling380forEmergency = 0
#This config is enable RAT measurements of PDN bring-up / HO cases for Verizon in home network for idle cases.
bEnableVzwIdleHomeMeasurements = 0
[MEDIA:MediaDscp]
#This config item specifies dscp value for audio
audio = 46
#This config item specifies dscp value for video
video = 30
[QIPCALL:ImsVideoModifyConfig]
#This config is required to configure the timer in msecs for
#waiting on user response to the incoming upgrade req.
localUpgradeAcceptTimer = 20000
#This config is required to configure the timer in secs for
#response from the peer to the sent upgrade req.
remoteUpgradeRejectTimer = 40
[SIPConfig:CustomTimers]
#reliable response retry timer cap in milliseconds
TRelResponseRetry = 0
"
Android 12 · version 33000000665 current release 
Android 11 · version 25000000626 same content 
Android 10 · version 14000000502 same content