· efs:/efsprofiles/overideconfig = "
[SIPConfig:GeoLocation]
#enable or disable location info inclusion in regular calls
iEnableCellInfoInPANI = 0
#enable or disable location info inclusion in regular calls
iEnableLocInfoInNormalCall = 0
#enable or disable location info inclusion in emergency calls
iEnableLocInfoInEmergencyCall = 1
#to set the threshold for uncertainty validation
fUnCertaintyThreshold = 0.0
[QIPCALL:H264_2]
#This config is to specify the profile for H264. Only use value 1
#The possible values of this enum are:
#/** Invalid Profile*/
#QP_CONFIG_IMS_H264_PROFILE_INVALID = 0x00,
#/** Baseline Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_BASELINE = 0x01,
#/** Main Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_MAIN = 0x02,
#/** Extended Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_EXTENDED = 0x03,
#/** High Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_HIGH = 0x04
profile = 1
#Preffered resolution. Possible values:
#INVALID_RESOLUTION = 0,
#PORTRAIT_SQCIF_RESOLUTION, // 1
#LANDSCAPE_SQCIF_RESOLUTION, // 2
#PORTRAIT_QQVGA_RESOLUTION, // 3
#LANDSCAPE_QQVGA_RESOLUTION, // 4
#PORTRAIT_QCIF_RESOLUTION, // 5
#LANDSCAPE_QCIF_RESOLUTION, // 6
#PORTRAIT_QVGA_RESOLUTION, // 7
#LANDSCAPE_QVGA_RESOLUTION, // 8
#PORTRAIT_CIF_RESOLUTION, // 9
#LANDSCAPE_CIF_RESOLUTION, // 10
#PORTRAIT_VGA_RESOLUTION, // 11
#LANDSCAPE_VGA_RESOLUTION, // 12
#PORTRAIT_HD_720_RESOLUTION, // 13
#LANDSCAPE_HD_720_RESOLUTION, // 14
resolution_preferred = 8
#Preffered Framerate
framerate_preferred = 15
#payload type for packetization mode 0. number above 96
payload_type_packetization_mode0 = 117
#Codec level. possible values:
#INVALID_LEVEL = 0x00,
#Level 1 = 0x01,
#Level 1B = 0x02,
#Level 11 = 0x03,
#Level 12 = 0x04,
#Level 13 = 0x05,
#Level 2 = 0x06,
#Level 21 = 0x07,
#Level 22 = 0x08,
#Level 3 = 0x09,
#Level 31 = 0x0A,
#Level 32 = 0x0B,
#Level 4 = 0x0C,
#Level 41 = 0x0D,
#Level 42 = 0x0E,
#Level 5 = 0x0F,
#Level 51 = 0x10
level = 4
#payload type for packetization mode 1. number above 96 and
#different from packetization mode 0
payload_type_packetization_mode1 = 118
#AS value if IPv6 is used
ipv6_AS_value = 0
#Max Bitrate
bitrate_max = 335
#Preffered bitrate
bitrate_preferred = 335
#Min Bitrate
bitrate_min = 64
#Max Framerate
framerate_max = 15
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
#Min Framerate
framerate_min = 7
#Supported resolution
resolutions_supported = 0
#AS value if IPv4 is used
ipv4_AS_value = 0
[QIPCALL:H264_1]
#This config is to specify the profile for H264. Only use value 1
#The possible values of this enum are:
#/** Invalid Profile*/
#QP_CONFIG_IMS_H264_PROFILE_INVALID = 0x00,
#/** Baseline Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_BASELINE = 0x01,
#/** Main Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_MAIN = 0x02,
#/** Extended Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_EXTENDED = 0x03,
#/** High Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_HIGH = 0x04
profile = 1
#Preffered resolution. Possible values:
#INVALID_RESOLUTION = 0,
#PORTRAIT_SQCIF_RESOLUTION, // 1
#LANDSCAPE_SQCIF_RESOLUTION, // 2
#PORTRAIT_QQVGA_RESOLUTION, // 3
#LANDSCAPE_QQVGA_RESOLUTION, // 4
#PORTRAIT_QCIF_RESOLUTION, // 5
#LANDSCAPE_QCIF_RESOLUTION, // 6
#PORTRAIT_QVGA_RESOLUTION, // 7
#LANDSCAPE_QVGA_RESOLUTION, // 8
#PORTRAIT_CIF_RESOLUTION, // 9
#LANDSCAPE_CIF_RESOLUTION, // 10
#PORTRAIT_VGA_RESOLUTION, // 11
#LANDSCAPE_VGA_RESOLUTION, // 12
#PORTRAIT_HD_720_RESOLUTION, // 13
#LANDSCAPE_HD_720_RESOLUTION, // 14
resolution_preferred = 8
#Preffered Framerate
framerate_preferred = 15
#payload type for packetization mode 0. number above 96
payload_type_packetization_mode0 = 115
#Codec level. possible values:
#INVALID_LEVEL = 0x00,
#Level 1 = 0x01,
#Level 1B = 0x02,
#Level 11 = 0x03,
#Level 12 = 0x04,
#Level 13 = 0x05,
#Level 2 = 0x06,
#Level 21 = 0x07,
#Level 22 = 0x08,
#Level 3 = 0x09,
#Level 31 = 0x0A,
#Level 32 = 0x0B,
#Level 4 = 0x0C,
#Level 41 = 0x0D,
#Level 42 = 0x0E,
#Level 5 = 0x0F,
#Level 51 = 0x10
level = 4
#payload type for packetization mode 1. number above 96 and
#different from packetization mode 0
payload_type_packetization_mode1 = 116
#AS value if IPv6 is used
ipv6_AS_value = 0
#Max Bitrate
bitrate_max = 335
#Preffered bitrate
bitrate_preferred = 335
#Min Bitrate
bitrate_min = 64
#Max Framerate
framerate_max = 15
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
#Min Framerate
framerate_min = 7
#Supported resolution
resolutions_supported = 0
#AS value if IPv4 is used
ipv4_AS_value = 0
[QIPCALL:H264_0]
#This config is to specify the profile for H264. Only use value 1
#The possible values of this enum are:
#/** Invalid Profile*/
#QP_CONFIG_IMS_H264_PROFILE_INVALID = 0x00,
#/** Baseline Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_BASELINE = 0x01,
#/** Main Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_MAIN = 0x02,
#/** Extended Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_EXTENDED = 0x03,
#/** High Profile.*/
#QP_CONFIG_IMS_H264_PROFILE_HIGH = 0x04
profile = 1
#Preffered resolution. Possible values:
#INVALID_RESOLUTION = 0,
#PORTRAIT_SQCIF_RESOLUTION, // 1
#LANDSCAPE_SQCIF_RESOLUTION, // 2
#PORTRAIT_QQVGA_RESOLUTION, // 3
#LANDSCAPE_QQVGA_RESOLUTION, // 4
#PORTRAIT_QCIF_RESOLUTION, // 5
#LANDSCAPE_QCIF_RESOLUTION, // 6
#PORTRAIT_QVGA_RESOLUTION, // 7
#LANDSCAPE_QVGA_RESOLUTION, // 8
#PORTRAIT_CIF_RESOLUTION, // 9
#LANDSCAPE_CIF_RESOLUTION, // 10
#PORTRAIT_VGA_RESOLUTION, // 11
#LANDSCAPE_VGA_RESOLUTION, // 12
#PORTRAIT_HD_720_RESOLUTION, // 13
#LANDSCAPE_HD_720_RESOLUTION, // 14
resolution_preferred = 7
#Preffered Framerate
framerate_preferred = 15
#payload type for packetization mode 0. number above 96
payload_type_packetization_mode0 = 113
#Codec level. possible values:
#INVALID_LEVEL = 0x00,
#Level 1 = 0x01,
#Level 1B = 0x02,
#Level 11 = 0x03,
#Level 12 = 0x04,
#Level 13 = 0x05,
#Level 2 = 0x06,
#Level 21 = 0x07,
#Level 22 = 0x08,
#Level 3 = 0x09,
#Level 31 = 0x0A,
#Level 32 = 0x0B,
#Level 4 = 0x0C,
#Level 41 = 0x0D,
#Level 42 = 0x0E,
#Level 5 = 0x0F,
#Level 51 = 0x10
level = 4
#payload type for packetization mode 1. number above 96 and
#different from packetization mode 0
payload_type_packetization_mode1 = 114
#AS value if IPv6 is used
ipv6_AS_value = 0
#Max Bitrate
bitrate_max = 384
#Preffered bitrate
bitrate_preferred = 384
#Min Bitrate
bitrate_min = 64
#Max Framerate
framerate_max = 15
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
#Min Framerate
framerate_min = 7
#Supported resolution
resolutions_supported = 0
#AS value if IPv4 is used
ipv4_AS_value = 0
[QIPCALL:EVS_0]
#channel aware setting
ch_aw_recv = 3
#This config is used for hf only
hf_only = 0
#This config is bandwidth.
#enum - BW_NB, BW_WB, BW_SWB, BW_FB, BW_NB_WB, BW_NB_SWB, BW_NB_FWB,
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
Bandwidth = BandWidth_SWB
#This config is used for bit rate. It has to be in DECIMAL format.
BitRate = 16
[QIPCALL:EVS_1]
#channel aware setting
ch_aw_recv = 2
#This config is bandwidth.
#enum - BW_NB, BW_WB, BW_SWB, BW_FB, BW_NB_WB, BW_NB_SWB, BW_NB_FWB,
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
Bandwidth = BandWidth_SWB
#This config is used for bit rate.
BitRate = 120
[QIPCALL:EVS_2]
#channel aware setting
ch_aw_recv = -1
#This config is bandwidth.
#enum - BW_NB, BW_WB, BW_SWB, BW_FB, BW_NB_WB, BW_NB_SWB, BW_NB_FWB,
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
Bandwidth = BandWidth_WB
#This config is used for bit rate.
BitRate = 120
[SMSDAN:USSDSettings]
#This config item controls the Language String to be used.
ussdLangString = ""
[QIPCALL:H265_2]
#payload type for packetization mode 0. number above 96
payload_type = 0
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
[Registration:RegistrationTimers]
#This config item controls the time in seconds to wait for WLAN RAT in wifi preferred mode for SSIM device
wlanGaurdTimer = 7
#This config item controls the Register configuration for the network-initiated De reg Timer value.
networkInitiatedDeRegistrationTimer = 60
#This config item controls the waiting time for sending Reg or Dereg. Unit is ms.
FTConsolidateTimer = 700
#This config item controls the Retry timer for permanent PDP failures
pdnRetryLongTimer = 1
#This config item controls the time in seconds to wait for WLAN RAT in wifi preferred mode for MSIM device
wlanGaurdTimerMSIM = 7
#This config item controls the time in seconds to wait for WWAN RAT in cellular preferred mode for SSIM device
wwanGaurdTimer = 45
#This config item controls the time in seconds to wait for WWAN RAT in cellular preferred mode for MSIM device
wwanGaurdTimerMSIM = 10
#This config item controls the Retry timer for temporary failures
pdnRetryShortTimer = 30
[QIPCALL:H265_0]
#payload type for packetization mode 0. number above 96
payload_type = 0
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
[QIPCALL:H265_1]
#payload type for packetization mode 0. number above 96
payload_type = 0
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
[Ut:UtConfiguration]
#This config is required to configure the server responses for which UT is to be blocked permanently
BlockUtResponseCodes = ""
#This config item controls the media element type for Call Barring Service. Possible values for override are as follows:
#QP_NO_MEDIA_TAG = 0 -->No media tag support
#QP_ONLY_VIDEO_TAG_FOR_VT = 1 -->One media tag per media type
#QP_AUDIO_AND_VIDEO_TAGS_FOR_VT = 2 -->include both audio and video tags
#QP_NO_MEDIA_TAG_FOR_VOICE_AND_ONLY_VIDEO_TAG_FOR_VT = 3 -->include Only video tag
mediaElementSupportForCB = 0
#This config item specifies if the realm is to trimmed or not. 0:Not enabled(default), 1:enabled
isTrimRealmEnabled = 0
#This config item specifies if IR92v10 is enabled or not. 0:Not enabled(default), 1:enabled
isIr92V10Enabled = 0
#This config item controls the time for which the PDN needs to be kept Active after a SS request is completed
pdnHysTimerValue = 0
#This config item controls the Maximum time within which a Response should be sent to UI
maxResponseTimerValue = 0
#This config item specifies if CFNL request is blocked with CFNRc. 0:Not enabled(default), 1:enabled
isCFNLBlockedwithCFNRc = 0
#This config item controls the action item when there is no SIB value for CB request. Possible values for override are as follows:
#QP_NO_HANDLING = 0 --> Default
#QP_REJECT_EMPTY_SIB = 1 --> Reject
#QP_AUDIO_RULE_ONLY = 2 --> Audio Only
#QP_AUDIO_AND_VIDEO_RULES = 3 --> Both Audio and Video
emptySIBUsageForCB = 0
#This config item controls the action item. When a rule id is not present in a server xml, a request is not allowed. It is used on VDF-Portugal only now. 0:Not to check a rule ID(Default), 1:Block a request when rule ID is not present in a server xml
blockIfRuleIDAbsent = 0
#This config item specifies if the GET request is to be sent at simservs node level. 0:Not enabled(default), 1:enabled
isReqAtSimservsNode = 0
[SIPConfig:FeatureFlags]
#enable or disable sip instance inclusion in contact header
IsSipInstanceNeeded = 0
#enable or disable Cellular-Network-Info header
IsCNIEnabled = 0
#enable or disable IsUserPartNeededForContactHeader
IsUserPartNeededForContactHeader = 1
#enable or disable header compact form
IsCompactFormEnabled = 1
#enable or disable IsUIReadyStatusCheckNeeded
IsUIReadyStatusCheckNeeded = 0
#disable StopTimerBon1xx once 1xx response is not received
StopTimerBon1xx = 0
#enable or disable IsImsiNeededForContactHeader
IsImsiNeededForContactHeader = 1
[QIPCALL:ImsVoiceSrvccConfig]
#This config is required to enable SRVCC based on contact header FT.
enableSRVCCOnContactHeader = 0
#This config is required to enable bSRVCC.
bSrvccEnabled = 0
#This config is required to enable aSRVCC.
aSrvccEnabled = 0
#This config is required to enable mid call SRVCC.
midcallSrvccEnabled = 0
[QIPCALL:ImsRtcpConfig]
#This config is required to configure the RR bandwidth for Video.
rrForVideo = 2000
#This config is required to configure the timer for RTCP
#monitoring.
rtcpLinkAlivenessTimer = 20
#This config is required to configure the RS bandwidth for Audio.
rsForAudio = 2500
#This config is required to disbale/enable the RTCP monitoring.
disableRTCPMonitoring = 0
#This config is required to configure the timer for RTCP
#Reporting in VT call.
rtcpReportingIntervalInVideo = 1
#This config is required to configure the RS bandwidth for Video.
rsForVideo = 600
#This config is required to configure the RR bandwidth for Audio.
rrForAudio = 2500
[QIPCALL:AMR_4]
#This config is bandwidth.
#enum - BW_NW, BW_WB
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
BandWidth = BandWidth_WB
#This config is modeset.
ModeSet = 4
#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA
#Possible INTEGER values for Mode are as follows:
#0 --> AMR_MODE_BE
#1 --> AMR_MODE_OA
#2 --> AMR_MODE_MAX
Mode = AMR_MODE_OA
[QIPCALL:G711_2]
#This config is dtx.
#0 - dtx disable
#1 - dtx enable
Dtx_enable = 1
#This config is to set G711 mode
#enum - G711_MODE_PCMU, G711_MODE_PCMA
#Possible INTEGER values for override Mode mask values are as follows:
#0 --> G711_MODE_PCMU
#1 --> G711_MODE_PCMA
#2 --> G711_MODE_MAX
Mode = G711_MODE_PCMA
[QIPCALL:G711_1]
#This config is dtx.
#0 - dtx disable
#1 - dtx enable
Dtx_enable = 1
#This config is to set G711 mode
#enum - G711_MODE_PCMU, G711_MODE_PCMA
#Possible INTEGER values for override Mode mask values are as follows:
#0 --> G711_MODE_PCMU
#1 --> G711_MODE_PCMA
#2 --> G711_MODE_MAX
Mode = G711_MODE_PCMU
[QIPCALL:G711_0]
#This config is dtx.
#0 - dtx disable
#1 - dtx enable
Dtx_enable = 1
#This config is to set G711 mode
#enum - G711_MODE_PCMU, G711_MODE_PCMA
#Possible INTEGER values for override Mode mask values are as follows:
#0 --> G711_MODE_PCMU
#1 --> G711_MODE_PCMA
#2 --> G711_MODE_MAX
Mode = G711_MODE_PCMU
[QIPCALL:AMR_0]
#This config is bandwidth.
#enum - BW_NW, BW_WB
#Possible INTEGER values for Bandwidth are as follows
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
BandWidth = BandWidth_NB
#This config is modeset.
ModeSet = 128
#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA
#Possible INTEGER values for Mode are as follows:
#0 --> AMR_MODE_BE
#1 --> AMR_MODE_OA
#2 --> AMR_MODE_MAX
Mode = AMR_MODE_BE
[QIPCALL:AMR_1]
#This config is bandwidth.
#enum - BW_NW, BW_WB
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
BandWidth = BandWidth_WB
#This config is modeset.
ModeSet = 4
#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA
#Possible INTEGER values for Mode are as follows:
#0 --> AMR_MODE_BE
#1 --> AMR_MODE_OA
#2 --> AMR_MODE_MAX
Mode = AMR_MODE_BE
[QIPCALL:AMR_2]
#This config is bandwidth.
#enum - BW_NW, BW_WB
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
BandWidth = BandWidth_NB
#This config is modeset.
ModeSet = 128
#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA
#Possible INTEGER values for Mode are as follows:
#0 --> AMR_MODE_BE
#1 --> AMR_MODE_OA
#2 --> AMR_MODE_MAX
Mode = AMR_MODE_OA
[QIPCALL:AMR_3]
#This config is bandwidth.
#enum - BW_NW, BW_WB
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
BandWidth = BandWidth_NB
#This config is modeset.
ModeSet = 128
#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA
#Possible INTEGER values for Mode are as follows:
#0 --> AMR_MODE_BE
#1 --> AMR_MODE_OA
#2 --> AMR_MODE_MAX
Mode = AMR_MODE_BE
[QIPCALL:ImsVoiceQoSConfig]
#This config is required to enable sending SDP answer in PRACK
#for 183 if the local qos is granted before 183 response is recvd by
#the UE.
qosOptimization = 0
#This config is required to configure the timer for dedicated
#bearer allocation.
qosReservationTimer = 8000
#This config is required to enable set the desired qos strength
#for local and remote UEs.
qosDesiredStrength = 1
#This config is required to enable 183 for Reneg
qosMc183 = 0
#This config is required to configure if the UE must wait for
#video dedicated bearer allocation during call setup.
localQosResReqVideo = 0
#This config is required to configure if the UE must wait for
#text dedicated bearer allocation during call setup.
localQosResReqText = 0
#This config is required to enable qos call flow when call is on wifi
simulateQoSInWifi = 0
#This config is required to enable/disable video CRBT feature
VideoCRBT = 0
#This config is required to configure the early QoS timer for video dedicated
#bearer allocation.
earlyQosReservationTimer = 0
#This config is required to enable Qos precondition negotiation
#in SDP.
qosPreconditionsEnabled = 0
#This config is required to enable Qos MC precondition negotiation
#in SDP.
qosMcPreconditionsEnabled = 0
#This config is required to configure the MBR threshold.
iMBRthresholdValue = 0
#This config is required to configure if the UE must wait for
#audio dedicated bearer allocation during call setup.
localQosResReqAudio = 0
#This config is required to configure if the initial SDP
#directionality should be inactive in REINVITE when preconditions are
#used
reinviteSdpDirInactive = 0
#This config is required to enable MBR check for video bearer.
qosMbrVideoCheckReqEnabled = 1
#This config is required to configure if the initial SDP
#directionality should be inactive when preconditions are used.
inviteSdpDirInactive = 0
#This config is required to start Mid-call qos timer after HO from Wifi to LTE is success
startMcqosAfterHOfromWifitoLte = 0
#This config is required to enable MBR check for audio bearer.
qosMbrAudioCheckReqEnabled = 0
#This config is required to enable QCI match with the requested media type for qos
checkQciForQoSMediaType = 0
#This config is required to enable mid-call precondition for Call Hold/Resume
qosMcHold = 0
[Ut:XCAPCommonHC]
#This config item controls whether GBA_U is enabled or not
useGBAMEOnly = 0
#This config item controls whether ims prefix is added or not for Ub request like as bsf.ims.mnc005.mcc232.pub.3gppnetwork.org
includeIMSPrefixForUSIM = 0
#This config item controls whether to ignore RSp Auth failure or not
IgnoreRSPAuthFailure = 0
#This config item controls the configuration of BSF server address
bsfServerAddress = ""
#This config item controls whether to use user mode for TLS
useUserModeForTLS = 0
#This config item controls whether BSF server supports TLS. Possible values for override are as follows:
#eQP_IMS_XCAP_GBA_TLS_MODE_OVER_UB_NONE = 0 --> not enabled
#eQP_IMS_XCAP_GBA_TLS_MODE_OVER_UB_ON = 1 --> Enabled
bsfServerTlsSupport = 0
[Registration:RegistrationFeatureFlags]
#This config item specifies if the sub operator is APTG and special handling is required for Options unsubscribed error or not. 0:Not enabled(default), 1:enabled
optionsUnsubscribedSpecialHandling = 0
#This config item controls whether need to reset AWT timer.
notResetAWTTimerEnable = 0
#This config item controls whether Perm block over IWLAN need to reset or not.
resetPermblockOverIwlan = 0
#This config item controls whether IWLAN Config failure is to be handled as internal failure.
specialhandlingForIWLANConfigFailure = 0
#This config item controls whether measurement on IWLNA should be ignored during APM on.
IgnoreWiFiMeasurementDuringAPMOn = 0
#send VoLTE ON/OFF indication to CM when non-DDS
*ForceVolteStatusIndication = 1
[QIPCALL:EVS_3]
#channel aware setting
ch_aw_recv = 2
#This config is bandwidth.
#enum - BW_NB, BW_WB, BW_SWB, BW_FB, BW_NB_WB, BW_NB_SWB, BW_NB_FWB,
#Possible INTEGER values for Bandwidth are as follows:
#0 --> BandWidth_NB
#1 --> BandWidth_WB
#2 --> BandWidth_SWB
#3 --> BandWidth_FB
#4 --> BandWidth_NB_WB
#5 --> BandWidth_NB_SWB
#6 --> BandWidth_NB_FWB
#7 --> BandWidth_MAX
Bandwidth = BandWidth_WB
#This config is used for bit rate.
BitRate = 120
[QIPCALL:ImsVoiceSessionTimerConfig]
#This config is required to configure the session refresher shall
#be UAC/UAS.
#Possible enum values are as follows:
#QP_CONFIG_SES_REFRESHER_UAC =0, UAC will go out as the refresh parameter in the initial Refresh Request
#QP_CONFIG_SES_REFRESHER_UAS =1, UAS will go out as the refresh parameter in the initial Refresh Request
#QP_CONFIG_SES_REFRESHER_UNKNOWN =2 UNKNOWN
sessionRefresherType = QP_CONFIG_SES_REFRESHER_UNKNOWN
#This config is required to enable session timer support.
sessionTimerEnabled = 1
#This config is required to enable Stand Alone Session Expiry
#negotiation.
standAloneEnabled = 1
#This config is required to enable Sesssion Expiry timer
#negotiation.
allowSeNegotiation = 0
#This config is required to configure the method for session
#referesh shall be REINVITE/UPDATE.
#Possible enum values are as follows:
#QP_CONFIG_SES_REFRESH_UNKNOWN = -1, UNKNOWN
#QP_CONFIG_SES_REFRESH_INVITE, INVITE will be the refresh method used
#QP_CONFIG_SES_REFRESH_UPDATE
sessionRefresherMethod = QP_CONFIG_SES_REFRESH_UPDATE
[QIPCALL:ImsVoiceConfig]
#This config is required to configure the Emergency call Cancel Timer.TImer is started when UE triggered CANCEL and waiting for 200 OK of CANCEL from network
emergencyCallCancelTimer = 500
#This config is required to configure the default WPS invite duration.
wpsInviteDuration = 0
#This config is required to enable 380 response validation as per
#3GPP.
enableAlternateSrvRspCheck = 1
#This config is required to set the display text priority
#subscription.
displayTextPriority = 3
#This config is required to include MTT USSD feature tag into IMS registration.
ussdAcceptContact = "+g.3gpp.nw-init-ussi"
#This config is required to configure the default invite retry counter.
inviteRetryCounter = 2
#This config is required to select the default emergency URI if sub category matches with multiple entries
e911SelectDefURI = 0
#This config is required to configure Call Waiting indication to UI
enableCWI = 0
#This config is required to disable early media timer.
disableEarlyMediaTimer = 0
#This config is required to configure the voice call Cancel Timer.TImer is started when UE triggered CANCEL and waiting for 200 OK of CANCEL from network
voiceCallCancelTimer = 0
#This config is required to place AMR WB before AMR in encryption call.
preferAMRWBinEncryptionCall = 0
#This config is required to enable PEM header in 183.
enablePEMHeaderIn183 = 0
#This config is required to configure the default URI type
#(SIP/TEL) for MO calls.
#Possible INTEGER values for the enum are as follows:
#QPE_IMS_URI_INIT = 0, enum value 0
#QPE_IMS_URI_SIP = QPE_IMS_URI_INIT, enum value 0
#QPE_IMS_URI_TEL, enum value 1
#QPE_IMS_URI_ANY, enum value 2
#QPE_IMS_URI_MAX enum value 3
uriType = QPE_IMS_URI_TEL
#This config is required to configure the enabling of sending REINVITE
#during Active calls HO.
reInviteonHOforActiveCalls = 0
#This config is required to accommodate Network issue with symmetric payload for both TX/RX stream from Remote UE
supportSymmetricPTforTxRx = 0
#This config is required to configure the terminating identity presentation or restriction type.
terminatingIdentityService = 0
#This config is required to configure the default WPS fallback duration.
wpsFallbackDuration = 0
#This config is required to enable the playing of local hold tone.
enableLocalHoldTone = 0
#This config is required to configure the ignoring of AS value
ignoreASValidation = 0
#This config is required to disable the default jitter buffer config
disableDefaultJBConfig = 0
#This config is required to configure the max-red value
max_red = 0
#This config is required to set error code for CT submode.
sessionEndResponseTimeout = 0
#This config is required to enable VoWIFI Call Continuity to LTE NonVOPS.
enableVCCtoLTENonVOPS = 0
#This config is required to enable the propagation of multiple 180 to UI.
enableMultiple180PropagationToUI = 0
#This config is required to enable emergency call operation in CS-only mode.
emergCallCSOnly = 0
#This config is required to configure number format during roaming, geo-local/home-local
#The possible INTEGER values for this enum are as follows:
#QPE_IMS_PHONE_CONTEXT_GEO_LOCAL = 0,
#QPE_IMS_PHONE_CONTEXT_HOME_LOCAL = 1
phoneContextPolicy = QPE_IMS_PHONE_CONTEXT_GEO_LOCAL
#This config is required to decide whether AMR BE fallback needs to be disabled
disableAMRBEFallBack = 0
#This config is required to consider a Normal call for end on Re-Reg Failure.
#e911 calls are by default allowed to continue till network tears it down.
endCallOnReRegFailure = 0
#This config is required to set reason Header Type.
reasonHeaderCustomizationType = 0
#This config is required to enable Call end on RTP inactivity.
CallEndonRTPInactivity = 0
#This config is required to set the phone context domain source.
#Possible INTEGER values for this enum are as follows:
#QPE_IMS_PHONE_CONTEXT_SOURCE_FROM_MCC_MNC = 0,
#QPE_IMS_PHONE_CONTEXT_SOURCE_FROM_PAU_HEADER = 1,
#QPE_IMS_PHONE_CONTEXT_SOURCE_PRE_DEFINED = 2,
PhoneContextSource = QPE_IMS_PHONE_CONTEXT_SOURCE_FROM_MCC_MNC
#This config is required to set preconditions enabled with qos events ignored.
ignoreQOSEvents = 0
#This config is required to enable the MT USSI.
enableMTUSSI = 1
#This config is required to configure the privacy type. Set 0: for none, 1: for id, 2: for header.
privacyType = 2
#This config is required to retain local SDP direction when incoming message has no PEM header.
PEMRetainLocalDirOnPeerNone = 0
[Registration:RegistrationDefaultParams]
#This config item will be used to configure default UserName to register with Network
userName = ""
#This config item will be used to configure default authType to register with Network
authType = ""
#This config item will be used to configure default Display Name to register with Network
displayName = ""
#This config item will be used to configure default DomainName to register with Network
domainName = ""
#This config item will be used to configure default authSecertKey
authSecertKey = "465b5ce8b199b49faa5f0a2ee238a6bc"
#This config item will be used to configure default Private URI to register with Network
privateURI = ""
#This config item will be used to configure default is3GPP
is3GPP = 0
#This config item will be used to configure default Realm to register with Network
realm = ""
#This config item will be used to configure default public URI to register with Network
publicURI = ""
#This config item will be used to configure default Password to register with Network
password = ""
[QIPCALL:ImsVoiceSuppsConfig]
#This config is required to configure the timer for Notify
#response to Refer.
notifyReferRspTimer = 20
#This config is required to end the conference call automatically
#when all other participants left the call.
endConfCallUponNoParticipant = 1
#This config is required to enable presentation of the call to
#the user when UE is already in two calls (active and held).
presentThirdCalltoUser = 0
#This config is required to skip dialing out status participent from adding in conference list.
skipDialingOutStatus = 0
#This config is required to configure the conference event
#package subscription timer.
confEvtSubTimer = 3600
#This config is required not to send unsubscribe to NW for conference call when there is
#no notify-terminated received.
isUnsubcribeDisabled = 0
#This config is required to configure the dialog for the
#conference event subscribe request.
confEvtSubOutOfDialog = 0
#This config is required to configure the three party conf URI
#for KDDI.
threePartyConfFactoryUri = ""
#This config is required to end the conference call automatically
#when user-count node in the CEP XML is 1.
endConfCallBasedOnUserCountNode = 0
#This config is required to enable the conference event package
#subscription.
#Possible enum values are as follows:
#QPE_IMS_CONF_PCKG_NONE = 0,
#QPE_IMS_CONF_PCKG_ALL = 1,
#QPE_IMS_CONF_PCKG_ORIGINATOR_ONLY = 2,
#QPE_IMS_CONF_PCKG_ORIGINATOR_ONLY_NO_JOIN_IND = 3,
#QPE_IMS_CONF_PCKG_PARTICIPANT_NO_SUBSCRIBE_NO_INDICATION = 4
confEvtPakageEnabled = QPE_IMS_CONF_PCKG_ORIGINATOR_ONLY
[QIPCALL:ImsRtcpXRConfig]
#This config is required to enable RTCP-XR support.
rtcpXrEnabled = 1
[SMSDAN:DANSettings]
#This config item controls QIPCall 1x SMS and Voice Enabled (0:DAN SMS can be sent only if there is no voice call.
#1:Enabled; DAN and MO SMS can be sent even when a voice call is up).
smsAndVoiceOver1x = 1
#This NV item is used for configuring the transport channel preference on which DAN is to be sent.
channelPreference = 1
#This config item controls the DAN Retry Timer Interval Duration (In ms)
retryTimer = 20000
#This config item controls the DAN Max Retry Counter
maxRetryCount = 3
#This NV item is used for controlling DAN Hysterisis Timer Duration
hysterisisTimer = 15000
[QIPCALL:H263_0]
#payload type number above 96
payload_type = 0
#This config is to ensure if the configuration is included in the
#offer
exclude_config_from_offer = '0'
[Registration:RegistrationCounters]
#This config item controls the Immediate Retry timer for failures
maxPDNIntermediateRetries = 2
[QIPCALL:ImsVideoConfig]
#This config is required to set the hold_downgrade_supported for VT
#calls.
hold_downgrade_supported = 0
#This config is required to configure the LTR mode.
#Possible enum values are as follows:
#/** Always disabled */
#QP_CONFIG_IMS_LTR_DISABLED = 0x00,
#/** Only enable for qc to qc devices negotiated via SDP */
#QP_CONFIG_IMS_LTR_ENABLED_RESTRICT_QC = 0x01,
#/** Always enabled */
#QP_CONFIG_IMS_LTR_ENABLED_ALL = 0x02,
ltrMode = QP_CONFIG_IMS_LTR_DISABLED
#This config is required to configure if VT capability can be impacted by modile data.
vtImpactedByMobileData = 1
#This config is required to set the video_capability_for_invite_no_sdp for
#incoming INVITE without SDP.
video_capability_for_invite_no_sdp = 1
#Internal:This config is required to store peer supported
#services
trackPeerServices = 1
[SIPConfig:Transport]
#above this size choose TCP and value 0 means disable tcp port open on UE
TCPThresholdValue = 1220
#enable or disable TCP Static threshold
TCPEnableStaticThreshold = 1
[SIPConfig:StandardTimers]
#sip registration expires value in milliseconds
SipRegValue = 600000
#sip reg subscription expires value in milliseconds
SipSubscribeValue = 600000
[SIPConfig:IPSec]
#integrity scheme for ipsec sip messages
#Possible INTEGER values for override Integrity Algorithm mask values are as follows:
#0 --> Invalid - none of the algorithm is supported
#1 --> alg=hmac-sha-1-96
#2 --> alg=hmac-md5-96
#3 --> alg=hmac-sha-1-96 and alg=hmac-md5-96
IntScheme = 0
#encryption algo for ipsec sip messages
#Possible INTEGER values for override Encryption Algorithm mask values are as follows:
#0 --> Invalid - none of the algorithm supported
#1 --> ealg=null;
#2 --> ealg=aes-cbc;
#3 --> ealg=null; ealg=aes-cbc;
#4 --> ealg=des-ede3-cbc;
#5 --> ealg=des-ede3-cbc; ealg=null;
#6 --> ealg=des-ede3-cbc; ealg=aes-cbc;
#7 --> ealg=des-ede3-cbc; ealg=aes-cbc; ealg=null;
EncAlgo = 0
[IMS_COMMON:ImsCommonTestModeCellId]
#This config item controls the test mode value
#eCELLID_TEST_MODE_OFF 0
#eCELLID_TEST_MODE_ON 1
CellID_Test_Mode = 0
#This config item controls the Cell ID value
CellID = ""
[SMSDAN:SMSSettings]
#This config item used to configure the error code and used while reject Incoming MT sms while NAS is busy in service one SMS.
IncomingSmsRejectCode = 400
#This config is required to enable addition of Accept-contact header field in MO SMS.
smsAcceptContactEnabled = 0
#This config item controls the SMS Feature tag
smsAcceptContact = "+g.3gpp.smsip"
#This config item used to enable or disable feature of rejecting incoming SMS when IMS is already processing a SMS.
EnableIncomingSmsRejectFeature = 0
[MEDIA:MediaCommon]
#This config item specifies if overall rate adaptation feature is enabled or not.
audioRAEnable = 1
#This config item specifies if NO_DATA format rtp pkts send is enabled or not.
rtpNoDataSend = 0
#This config item specifies maximum mtu size for the rtp packet
mtuSize = 1400
[Registration:RegistrationSettings]
#This config item controls Registration over IWLAN in airplane mode
#Possible INTEGER values for override are as follows:
#QPE_ENABLE_REG_INLPM_INVALID = 0 --> Reserved, Not to be used.
#QPE_ENABLE_REG_INLPM_OFF = 1 --> Registration is not on IWLAN as well enabled during LPM ON.
#QPE_ENABLE_REG_INLPM_ON = 2 --> Registration is enabled on IWLAN during LPM ON.
enableRegistrationInLPM = 2
#This config item controls PCSCF IP fallback feature
pcscfBasedIPFallback = 0
#This config item controls TTY over IMS
enableTTYOverIMS = 1
#This config item controls Reregistration over WIFI during Activate 3G call
#Possible INTEGER values for override are as follows:
#eQP_IMS_REG_OVER_WIFI_WHILE_ACTIVE_GSM_CALL_DISABLED = 0 --> Reg over WiFi is enabled by default irrespective of calls.
#eQP_IMS_REG_OVER_WIFI_WHILE_ACTIVE_2G_3G_CALL = 1 --> Reg over WiFi is blocked during 2G/3G calls
#eQP_IMS_REG_OVER_WIFI_WHILE_ACTIVE_3G_CALL_ONLY = 2 --> Reg over WiFi is blocked only during 3G calls
#eQP_IMS_REG_OVER_WIFI_WHILE_ACTIVE_2G_CALL_ONLY = 3 --> Reg over WiFi is blocked only during 2G calls
BlockRegOverWifiWhileActiveCSCall = 0
#This config item controls Reregistration over WIFI during Activate 1x call
BlockRegOverWifiWhileActive1XCall = 0
[Ut:XcapHCConfigUserProfile]
#This config item controls the configured user name
configUserName = ""
#This config item controls the configured user name
configUserPassword = ""
[DPL:Common]
#This config is used to enable/disable Dynamic UserAgent update
DisableUserAgentUpdate = 0
#Timer Var to delay in sending ISIM STATUS after initialization
ISIMStatusTimerVar = 5
#This config item determines usage to read the SIM card parameters (ISIM, USIM ) etc
#Possible INTEGER values for override are as follows:
#QPE_CONFIG_IMS_FILE_READ = 0 --> File Read Param Source
#QPE_CONFIG_IMS_NV_READ = 1 --> NV Read Param Source
#QPE_CONFIG_IMS_CARD_READ = 2 --> Card Read Param Source to read from ISIM
#QPE_CONFIG_IMS_FILE_READ_AUTH_ENABLED = 3 --> File Read Param Auth enabled (ONLY for testing)
#QPE_CONFIG_IMS_USIM_FB_MODE_ENABLED = 4 --> USIM fallback enabled
ParamSrc = QPE_CONFIG_IMS_CARD_READ
[QIPCALL:ImsMediaProfileConfig]
#This config is required to video codec profile list on 4G.
VideoProfile1 = "H264_0"
#This config is required to audio codec profile list.
AudioProfile1 = "EVS_0_109;AMR_1_104;AMR_4_110;AMR_0_102;AMR_2_108;AMR_3_106"
[QIPCALL:ImsVoWifiConfig]
#This config is required to configure the information to be passed
#in P-Emergency-Info header.
PEIHeaderInfoForEmergency = 0
#This config is required to configure the wifi connectivity
#backoff timer.
wifiConnectivityBackoffTimer = 0
#This config is required to configure the 380 handling for Emergency calls
#Possible values are:
#0 -> Default behaviour present in the code
#1 -> Force CSFB
#2 -> Send Permanent failure
Handling380forEmergency = 0
#This config is enable RAT measurements of PDN bring-up / HO cases for Verizon in home network for idle cases.
bEnableVzwIdleHomeMeasurements = 1
[MEDIA:MediaDscp]
#This config item specifies dscp value for audio
audio = 46
#This config item specifies dscp value for video
video = 46
[QIPCALL:ImsVideoModifyConfig]
#This config is required to configure the timer in msecs for
#waiting on user response to the incoming upgrade req.
localUpgradeAcceptTimer = 55000
#This config is required to configure the timer in secs for
#response from the peer to the sent upgrade req.
remoteUpgradeRejectTimer = 60
[SIPConfig:CustomTimers]
#reliable response retry timer cap in milliseconds
TRelResponseRetry = 0
"
Pixel 11 Pro Fold 
Pixel 11 Pro XL 
Pixel 11 Pro 
Pixel 11 
Pixel 10a 
Pixel 10 Pro Fold 
Pixel 10 Pro XL 
Pixel 10 
Pixel 10 Pro 
Pixel 9a 
Pixel 9 
Pixel 9 Pro XL 
Pixel 9 Pro Fold 
Pixel 9 Pro 
Pixel 8a 
Pixel 8 
Pixel 8 Pro 
Pixel Fold 
Pixel 7a 
Pixel 7 
Pixel 7 Pro 
Pixel 6a 
Pixel 6 Pro 
Pixel 6 
Pixel 5a 
Pixel 5 
Pixel 4a (5G) 
Pixel 4a 
Pixel 4 
Pixel 4 XL 
Pixel 3a 
Pixel 3a XL 
Pixel 3 XL 
Pixel 3 
Pixel 2 
Pixel 2 XL 
Pixel 
Pixel XL 
Android 12 · version 33000000490 current release 
Android 11 · version 25000000483 
Android 10 · version 14000000461